Lennox HVAC Service Nationwide | Dalton Heating & Air Fort Worth

Why Fort Worth Homeowners Choose Lennox HVAC

Dalton Heating & Air Fort Worth provides independent Lennox service in Fort Worth, including HVAC repair, installation, and maintenance across Tarrant County, and we work on these units every week. Our techs know the failure patterns specific to Fort Worth: dust-clogged condenser coils from nearby construction, heat-exchanger stress from clay-heavy soil shifting slabs, and attic-mounted units baking in 150°F summer heat. We are not authorized by Lennox and we don’t pretend to be. What we are is factory-trained on Lennox equipment with a written price before any work starts and a full-year written guarantee on every repair. Call (817) 730-5369 for Lennox service that actually shows up.

Call (817) 730-5369

Why Trust Dalton Heating & Air Fort Worth for Your Lennox HVAC?

Lennox builds good equipment, but good equipment fails in predictable ways. The technicians who fix it well are the ones who have seen those failures enough times to diagnose them in twenty minutes instead of three hours. Our crew has been servicing Lennox Signature, Elite, and Merit series equipment across Fort Worth long enough to know what a G61MPV blower module failure sounds like before we even open the panel. Marco Benitez, our owner, learned HVAC at Los Angeles Trade-Technical College and spent close to two decades working systems across the Southwest. He treats refrigerant and airflow mysteries other techs have already walked away from as a personal challenge. That’s the standard every tech on our crew works to.

We use OEM Lennox parts where the failure mode demands it: SureLight ignitors, Quantum evaporator coils, variable-speed inducer assemblies. We also tell you plainly when a quality aftermarket capacitor or contactor will do the same job for less money. The goal is a correct diagnosis and a repair that holds. Not a parts markup. Every AC repair we do on Lennox in Fort Worth carries our written guarantee for a full year. If the repair fails in that time, we return at no charge. That’s the Garrison Standard, and it has been our operating rule since 2003. Our service area runs from the Fairmount Historic District out through the Keller-Haslet sprawl north of Loop 820, and west into the newer builds past downtown.

Common Lennox HVAC Problems We Fix in Fort Worth

• Variable-speed blower motor module failures on G61MPV and SLP98V furnaces. These furnaces use an ECM (electronically commutated motor) with a control module that runs hot. After seven to ten years, the module quits talking to the motor and you get a dead blower or one that runs at a single speed. We see this constantly in Fort Worth because our winters cycle the heat on and off enough to cook the module’s capacitors. The fix is usually a module replacement, sometimes the whole motor. We stock both.
• Condenser fan motor bearing wear on 13ACX and XC14 units. Fort Worth sits in a dust corridor. Add cottonwood from the Trinity River bottoms and construction dust from the subdivisions going up around Haslet and Saginaw, and those condenser coils load up with a gray paste. The fan motor bearings work against that resistance until they seize or squeal. We clean the coil, check the amp draw, and replace the motor when the bearings are wiped.
• Evaporator coil leaks on older HS26 and 10ACB models. These are the 1990s and early-2000s Lennox units still running in Arlington Heights and near the Near Southside. Copper-aluminum coils that have lived through twenty Fort Worth summers develop pinhole leaks, and our hard water leaves scale on the drain pan that accelerates corrosion at the coil’s base. When the coil leaks on a unit this old, we walk you through the repair-vs-replace math honestly. Often the answer is replace the coil, but sometimes the condenser is three years behind it. We’ll tell you which one you’re looking at.
• Ignitor cracking on 80MGF and G40DF series furnaces. These older mid-efficiency Lennox furnaces use a silicon nitride ignitor that gets brittle after thousands of heat cycles. A cold snap hits Fort Worth in November, the furnace tries to fire, and the ignitor cracks instead of glowing. It’s a fast fix if we have the part on the truck. We keep them stocked for exactly this reason.
• Attic duct leakage compounding Lennox equiment problems. Not a Lennox part failure, but we’d be doing you a disservice if we didn’t name it. In the 1990s-2010s slab-on-grade tract homes that dominate Fort Worth, the flex duct in those low-pitch vented attics bakes brittle after fifteen years. A Lennox XC20 condenser can be running perfectly and still not cool the house because a third of the air is dumping into a 140°F attic. We check duct integrity on every Lennox cooling call, because skipping it means “fixing” a system that’s fighting a leak we can see from the attic hatch. Tell me what it is doing, and I will tell you what it needs.

Lennox Parts & Our Repair-vs-Replace Approach

When a Lennox unit fails, the question isn’t just what broke. It’s whether the repair makes sense on a unit of this age and condition. Here’s how we think about it.

OEM parts: We keep genuine Lennox parts in stock for the failures we see most often in Fort Worth. SureLight ignitors for the 80MGF and G40DF furnaces. Quantum evaporator coils for the older HS26-era units. ECM blower modules and complete blower motors for G61MPV and SLP98V furnaces. Variable-speed inducer assemblies. These are parts where the OEM version matters because the failure is specific to the engineering of that component.

Quality aftermarket parts: A capacitor is a capacitor. A contactor is a contactor. Where a quality aftermarket part from a known manufacturer is functionally identical and priced lower, we’ll tell you. We’re not going to charge OEM markup on a part that doesn’t earn it. That’s a real distinction, and it’s one most companies won’t make out loud.

Repair or replace: The honest rule we use: if the compressor or the heat exchanger has failed on a Lennox unit older than 12 years, repair is usually not worth it. You’re putting a new heart in an old body. On a 7-year-old SLP98V with a failed inducer motor, repair makes sense every time. We’ll put the decision in writing with real numbers, and the choice stays yours. Call (817) 730-5369 if you want that kind of straight answer.

Our Lennox Service Process – Step by Step

1. 1
   Diagnosis. We arrive inside the stated window, background-checked tech in a marked vehicle. We pull the error codes, check static pressure, test capacitor and amp draw, inspect the coil and heat exchanger, and look at the ductwork. On a Lennox variable-speed unit, we’re specifically checking the ECM module, the inducer, and the flame rod signal. Diagnosis is done before we quote anything.
2. 2
   Written price, then repair. You get the price in writing before any work begins. No exceptions. That’s the Garrison Code, and it applies to every Lennox furnace repair, AC repair, refrigerant recharge, or coil replacement we do in Fort Worth. You approve the number, then we turn wrenches.
3. 3
   Testing and verification. After the repair we run the unit through its cycles. We check temperature split. We verify airflow with a manometer. On a heat exchanger replacement we check flue draft and carbon monoxide with a combustion analyzer. A repair that “should be fine” isn’t done until we’ve measured that it is.
4. 4
   Written guarantee. Every Lennox repair carries a written guarantee for one full year. If the work fails inside that year, we return at no charge. Not a pro-rated credit. Not a diagnostic fee. We come back and fix it. That’s the 365-Day Done Right Promise.

Lennox Products We Service & Install in Fort Worth

We work on the full residential lineup. On the air conditioning side: the XC25 and XC20 from the Dave Lennox Signature Collection, the XC16 and EL296V from the Elite Series, and the ML14XC1 and ML180DF from the Merit Series. On furnaces: SLP98V and SLP99V variable-speed units, G61MPV and EL296V two-stage models, and the older 80MGF, G40DF, 13ACX, HS26, and 10ACB units still running across Fort Worth. We carry common Lennox OEM parts for fast same-visit fixes on emergency calls, and anything uncommon we can source same week. A few weeks ago our tech pulled a code E228 on a 2015 SLP98V in Arlington Heights: the variable-speed inducer was drawing 2.1 amps. OEM inducer assembly, manometer-verified airflow, and the family had heat before the evening cold front rolled in.

We Also Service These Brands

We service Lennox equipment daily, but we’re factory-trained across nine major residential brands. That matters, because most Fort Worth homes don’t have one brand in the attic and the same brand outside. We regularly service Carrier and Trane alongside Lennox, plus Goodman, Rheem, York, Daikin, Bryant, and American Standard. You call one number, you get a crew qualified on whatever is installed.

FAQs – Lennox HVAC Service in Fort Worth

Book Your Lennox Service in Fort Worth, TX

If you need Mansfield Lennox service, repair, or installation, call (817) 730-5369. A real person answers, 24/7. We’ll get your Lennox system diagnosed, priced in writing, and repaired right, with a full-year guarantee on every repair we make.

Written by Marco Benitez, Owner at Dalton Heating & Air Fort Worth, serving Fort Worth since 2003.